Configuration
Installation and Setup of Pressure Transducer with 4-20mA Output
This guide explains how to configure your Zenseio station and wire a 2-wire (loop-powered) 4–20 mA pressure transducer / transmitter using GPI2 + VAUX. These instructions are applicable only to pressure transducers with 4-20mA output. Pressure ...
RAK7268V2/RAK7268CV2 Indoor LoRaWAN Gateway Firmware Upgrade
ALERT: This firmware (WisGateOS 2) is applicable only to V2 version of RAK7268. Non-V2 RAK7268 or RAK7258 have different firmware WisGateOS. For non-V2 RAK7258 or RAK7268 firmware update, see here: ...
Connecting Davis Instruments Tipping Rain Bucket
Davis Instruments Rain Collectors with pulse output can be used with Zenseio LSMP and CSMP telemetry. Preparations Davis Rain Collectors have a proprietary plug. To use them with Zenseio devices, the sensor 's cable should be modified as follows: ...
Setting Up a Banner T30R Radar Sensor (4-20mA version)
Banner Engineering T30R radar level sensors with 4-20mA interface can be used with CSMP/LSMP telemetry devices Hook up: Brown (V+) input to VAUX White (4-20mA) into GPI2C Jumper from GPI2 to GND (next to GPI2) Blue (V-) into GND (next to VAUX) In the ...
Setting Up a Meter Group Phytos 31 Leaf Wetness Sensor with Your Zenseio Device
To set up a Meter Group Phytos 31 Leaf Wetness Sensor with your Zenseio Device: Note that this sensor model can only connect to GPI2 or GPI3 In Zenseio mobile configuration app: Set VAUX voltage output to 5V. Select “Voltage” mode on the chosen GPI ...
How to Connect a Temperature Sensor to a LSMP or CSMP Device
Temperature Sensor (Thermistor) Installation. Currently, only thermistors sold by Zenseio are supported. The following installation is for this thermistor only. Select “Thermistor (1-Wire)” mode in the Zenseio mobile phone configuration app ...
Configuring Alerts for GPI Sensors Using the Zenseio Mobile App
GPI I/O Mode - selects the functionality of the input: Off - the input is ignored Digital - a weak pullup voltage is supplied by device on the GPI input, and the input is sampled at Sensor Read Intervals. If the voltage is pulled externally close to ...
How to Configure VAUX Using the Zenseio Mobile App
5.3 VAUX Settings (LSMP or CSMP devices only) If the device is equipped with auxiliary voltage generator inputs, VAUX pin provides output voltage to power or bias an external sensor. Generated Output Voltage - sets the power supply voltage for the ...
Configuring Seametrics AG3000 Flow Meter for Zenseio Devices
Wiring For Seametrics AG3000 flow meter with pulse output, connect as follows: Connect Green (P3) Pulse+ wire to Zenseio GPI* (any GPI) connector Connect White (P4) Pulse- wire to Zenseio GND (next to GPI) connector ALERT: Do not connect Red (P1) DC+ ...
Installation and Setup of Pressure Transducer with Voltage Output
This guide explains how to configure your Zenseio station and wire a voltage pressure transducer / transmitter using GPI2 or GPI3 + VAUX. These instructions are applicable only to pressure transducers with voltage output. Pressure transducers with ...
RAK 7258/7268 Indoor LoRaWAN Gateway Firmware Upgrade
ALERT: This firmware (WisGateOS) is applicable only to non-V2 version of RAK7268 or RAK7258. RAK7268 V2 has different firmware WisGateOS 2. For RAK7268 V2 firmware update, see here: ...
Flow Meter Setup
Flow meter installation Attention: The Flow Meter must be configured to the pulse counter output with calibrated flow rates, which may vary between flow meter models. Please refer to the Flow Meter's Manual for more information on how to do this. ...